Building protects us from nature forces like rain, heat, cold, wind etc., The concrete structures on its own is porous and hence not watertight. The unprotected structures suffer from water induced damage including deterioration and corrosion caused by chlorination, oxidation and sulphation. They reduce alkalinity in concrete and turns acidic. The result, reinforcement bar catch rust and eventually expands, to drastically
hamper load bearing capacity of the building structures. The continuous presence of water leads to constant dampness & humidity and promotes the growth of molds and fungus on walls and insects presence leading to health problem like asthma, skin allergies, rashes etc., The consequent spalling of concrete plaster, flaking off expensive paint on interior/exterior ofwalls adversely impacts life and value of structure. If the buildings are notwaterproofed during constructions, itmay result in costlyandhassle pronerepairwork in future.
Monarch's technologically advancedMonoProof waterproofing systems cover every need of Building & Construction industry to protect from water ingress or loss of water through structures. The complete building structures frombasement to roof are protected from rising dampness, moisture, seepages and leakages from basement to roof. The technology ranges to acrylic SBR latex, crystalline, epoxy, water repellant polysiloxanes, polyurethane and bituminous based formulations. The coating fills and seals concrete pores, micro cracks and capillary tracts in joints,walls and floors through whichwater seep through and forms an integral waterproofing compound without breaking the existing brickbat cobaandconcrete screed.
MonoProof LWP is a two component acrylic modified elastomeric waterproofing which consists of specialty
hard-wearing aggregates and liquid acrylic emulsion. It is applied to waterproof and protect concrete and similar structures. Specially formulated for swimming pools, retaining wallspile Heads, water tanks, submerged tunnels, sumps, bridge decks, marbles, granites and a wide variety of extreme service class structures because on curing it forms an excellent elastomeric, waterproof & protective layer over the substrate . It is a seamless, waterproof coating providing a tough and durablewater tight coating which cannot be easily damaged orworn away.The coating is designed to re-face and even out variations in concreteandmasonry surfaces.This isaneasily brushable coating which canbesimply appliedby a stiff brush, or trowel to obtain the desired thickness. The polymer provides with exceptional adhesion, toughness and durability.MonoProof LWP effectively seals concrete masonry walls and bridges the shrinkage cracks which are static. The coating additionally protects against concrete decay providing a long lasting barrier towaterborne corrosive salts, freeze-thaw scaling, chloride, carbonation and atmospheric gases. A 1mm coating provides anti carbonation cover equivalent to over 80cmof concrete or air layer thickness for carbondioxide diffusion (R) of 92 meters.MonoProof LWP is showntoresist positivehydrostatic pressureupto 7 meterhead.
MonoProof AEW is a three-layer system with coats in different colors ensuring proper build-up of the
thickness, making it a reliable waterproofing system.MonoProof AEW is a two component acrylic modified elastomeric waterproofing which consists of specialty hard-wearing aggregates and liquid acrylic emulsion. It is applied to waterproof and protect concrete and similar structures. Specially formulated for swimming pools, retaining wallspile Heads, water tanks, submerged tunnels, sumps, bridge decks, marbles, granites and a wide variety of extreme service class structures because on curing it forms an excellent elastomeric, waterproof & protective layer over the substrate .It is a seamless, waterproof coating providing a tough and durablewater tight coating which cannot be easily damaged orworn away. The coating is designed to re-face and even out variations in concrete and masonry surfaces.This is an easily brush able coating which can simply be applied by a stiff brush, or trowel to obtain the desired thickness. The polymer provides with exceptional adhesion, toughness and durability. MonoProof AEW effectively seals concrete masonry walls and bridges the shrinkage cracks which are static.The coating additionally protects against concrete decay providing a long lasting barrier towaterborne corrosive salts, freeze-thawscaling, chloride, carbonation and atmospheric gases. A1mm coating provides anti carbonation cover equivalent to over 80cm of concrete or air layer thickness for carbon dioxide diffusion (R) of 92 metres. MonoProof AEW is shown to resist positive hydrostatic pressure up to 7 meter head MonoProofAEW is suitable for all types of structures including those in coastal environments.
MonoProof EW200 is a single Component 3 layer heavy duty terrace waterproof & heat reflective coating system, The Coating material specially developed highly elastic & resilient acrylic polymers, micro-fibers, additives & best quality fungicidal in water medium etc.
MonoProof EW200 is used as a liquid applied waterproofing & heat reflective membrane for all types of building terraces. The 3 layer system with coats in different colors ensuring proper build-up of the thickness, making it a reliable waterproofing & heat reflective coating system. The 3rd and final layer whitish coating containing low density, hollow ceramic microspheres reflects 98% of heat back to atmosphere still acting as elastomeric permanent waterproofing membrane. The coating in addition saves energy bills up to 20% of cooling and heating bills.
The coating performance can be enhanced for large roofs, by providing a fiber mesh that is embedded or sandwiched between the coats with special care to pipes, up stands, drains, projected line, coving, and other mechanical & electrical penetrations. The coatings are compatible for roofs ranging from asphalt and asbestos cement to terrazzo tiles and concrete as well as for horizontal and inclined roofs.
1st layer in grey color
2nd layer in ivory color
3rd layer in white color
MonoProof AG is a ready to use, one component waterproofing membrane composed of elastomeric polymers and proprietary chemicals. It can be used as a waterproof membrane & protective coatings for terraces, balconies, exterior walls and roof slabs. It accommodates limited crack movement in underlying surfaces. It develops an excellent bond to most building material hence becoming a part of concrete repair. MonoProof AG is trowel, brush, or roller applied to provide a continuous non-permeable waterproofing membrane to a variety of surfaces including concrete, masonry, laminates and cement backer boards.
MonoProof RG is composed of high quality acrylic emulsion polymer. It is used as a waterproofing protective coating for exterior walls of the concrete masonry buildings because it forms higher film thickness,has excellent "exibility, breathing properties, water resistance, crack-bridging ability, weathering durability and anexcellent resistance tothegrowthof microorganisms.
MonoBond SBR is a modified styrene butadiene rubber emulsion which is supplied as a ready to use
white liquid. It is designed to improve the quality of site‐batched cementitious mortars and slurries. Being
resistant to hydrolysis, it is ideal for internal and external applications in conjunction with cement. It used as
a bonding aid and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore
be used for external applications
MonoBond LMA Latex modified Acrylic is a white liquid polymer of low viscosity. It is specifically formulated for the use in structural concrete overlays, bridge decks and pavements where improved physical properties and improved bond are needed. MonoBond LMA also improves performance of sand-cement mortars for toppings and tile setting beds.
MonoProof FWP is 2 pack, solvent free epoxy material used for lining and Water proofing potable water
retaining structures and surfaces subject to contact with food stuffs. The material cures to provide a smooth, hygienic
and tough finish which is suitable for contact with potablewater and foodstuffs.The cured film is resistant to corrosion,
chemical attack and abrasion. The cured film is non-toxic and meets the requirements of IS: 9833 - 1981. The coating is
designedtobe applied in two coats to achieve aminimum total dryfilm thickness of 200 microns.
MonoProof DG is used as internal coating for the waterproofing treatments ofwater tanks and building walls
because it can be applied over damp surfaces, has excellentwater resistance, adhesion, hardness toughness and sets
faster similar to solvent based epoxy formulations. It has an advantage of dilution with water for application over
cementitious surfaces.
MonoProof SSP, is a clear, breathable, solvent-based, siloxane/silane penetrating water-repellent sealer used
to provide water repellent surface with improved self-cleaning properties on exterior building - brick work, concrete,
cement rendering, natural or cast stone. Helps in reducing efflorescence due to soluble salts in brickwork.The coating is
colorless and preserves natural color and texture of createdmaterial. It penetrates intoconcrete for aminimumdepth of
penetration of5mmensuringhydrophobic zone.
Permeability is low to water, salt solution, dust and soot particles. Leaching of soluble salts from brick work, which causes efflorescence, absorption of deicing salts by concrete which causes degradation and absorption of atmospheric dirtby brickwork, concreteandstoneare all minimized.
Monoproof WSP ( concentrate) is a water repellent state-of-art formulation, based on Silane / Siloxanes. It yields a stable emulsion. This emulsion produces a hydrophobic treatment that inhibits water absorption even on alkaline surfaces without significantly reducing water vapour permeability. Monoproof WSP provides water repellence within 24 hours of application. The water repellence further improves over a week after application. Can be used diluted or as supplied in the formulation of water repellent products. To prevent fungal growth within the package, additional preservative may be required. The product provides a long lasting effect as it penetrates the substrate being treated.
MonoProof PWP1K is a flexible, single component aliphatic liquid membrane. It cures to a permanently flexible seamless
membrane that has good adhesion to a wide range of substrates unlike more traditional bitumen based products. The
coating is crack-bridging, does not readily embrittle with age, exposure to ultra violet radiation or weathering, and hence
it does not crack or craze due to its flexible properties. It is elastomeric and hence not adversely affected by extremes of
temperature.
MonoProof PWP two component, aliphatic, thixotropic, non-yellowing, non-chalking, pigmented
polyurethane based elastomericwaterproof coating possessing good resistance to long termexposure of UV rays and
provides an easily cleaned coating. The cured !lm shall be protected with concrete screed / mortar when used on
accessible roofs toavoiddamagefromfoot traffic.
MonoMix WLA is applied to minimize permeability and increase the waterproofing properties of
concrete and cement sand mortars for critical applications. In addition to waterproofing the structure,
MonoMix WLA protects concrete against seawater, wastewater, aggressive ground water and many other
aggressive chemical solutions. MonoMix WLA is approved for use in contact with potable water, and is
therefore suitable for use in water storage tanks, reservoirs, water treatment plants, roof slabs and screeds,
basements, external plastering, bathroom floors, sumps, drains etc.
MonoMix IWP is applied to minimize permeability and increase the waterproofing properties of concrete and cement sand mortars for critical applications. In addition to waterproofing the structure, MonoMix IWP protects concrete against seawater, wastewater, aggressive ground water and many other aggressive chemical solutions. MonoMix IWP is approved for use in contact with potable water, and is therefore suitable for use in water storage tanks, reservoirs, water treatment plants, roof slabs and screeds, basements, external plastering, bathroom floors, sumps, drains etc.
MonoProof BWP is a ready mixed coating, brush applied bituminous, black, lead- free, acid, alkali, water and
chloride resistant that cures by reaction with atmospheric moisture to form a tough but fiexible waterproofing
membrane.Theyalsomeetthe requirements for coatings suitable for useonsurfaces in contact with potablewater.
MonoProof BWP are based on raw materials which are amongst the most water and water-vapor resistant surface coating materials available. They are also resistant to a wide range of chemical attack. Also to protect the concrete against effects of chlorinated water, and to inhibit algae growth and facilitate easier cleaning. The excellent chemical resistance of MonoProof BWP makes it particularly suitable for sub-structure applications in areas where chemical contaminantsandaggressivegroundwater conditions prevail.
Note : In common with all bituminous and tar based coatings, and many other organic materials,MonoProof BWP are susceptible to prolonged exposure to ultraviolet light and are not recommended for use in situations where they will be exposed to direct daylight. They are however, ideally suited for use in sandwich constructions, or as surface coatings in enclosed tanks or structures, or belowground,where their durability iswell proven.