The deterioration of concrete is influenced by a number of physical, chemical and environmental factors. it is very important that any damage to concrete must be repaired promptly in order not to compromise the integrity of structures built with concrete The Monarch’s MonoBuild range Repair, Rehabilitation & Strengthening materials can prolong the life of a structure way beyond its original design life., reducing the need to demolish and rebuild structures saving down-time and money. Repairs performed at early stage would save extremely expensive remediations that may become necessary at latter stages
MonoBuild PHF is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a highly consistent cementitious mortar. MonoBuild PHF exhibits excellent thermal compatibility with concrete, and is fully compatible with other MonoBuild PHF mortars. MonoBuild PHF is designed for application to minor imperfections in concrete and masonry surfaces. It is suitable for application in the range of feather edge to 3 mm
MonoBuild CS6 is a crack sealing cementitious material in powder form. It is composed of cement, select aggregates, polymer & additives which requires on site addition of water only. It is ideal to fill 3to 6 mm wider static cracks, for levelling up walls before tiling and for skimming expanded polystyrene and asbestos. It is easy to apply and can be finished or smoothened off with a putty blade or a damp sponge. It has strong adhesion, is non-shrink in nature, good water resistance properties & weathering durability. It sets quickly on application and can be over coated with common paints / coatings and it has enhances the subsequent paintings quality and life.
MonoBuild CS20 is a crack sealing cementitious material in powder form. It is easy to apply and can be finished or smoothened off with a putty blade or a damp sponge. It sets quickly on application and can be over coated with common paints / coatings. MonoBuild CS20 improves durability, compressive, tensile and flexural properties of modified mixes whilst reducing permeability, making it suitable for horizontal or vertical applications both internally and externally.
MonoBuild PER is polyester resin based grouting compound is supplied as two-component products with pre-weighed quantities of liquid resin and powdered hardener, ready for on-site mixing and use. The hardener system enables the mix to be varied from a pourable consistency to a trowellable mortar without significantly affecting the setting times or strengths achieved. This makes the product extremely reliable in use.
MonoBuild EP is a thixotropic, solvent free, two component compound based on water insensitive epoxy resins, inertfillers and thixotropic agents designed for applying in damp and submerged conditions. It is applied directly to concrete for filling cracks, blow holes etc., which cures to form a strong seal.
MonoBuild FPC mortar is supplied as a ready to use dry powder requiring only the addition of water to produce specially designed to provide a very fast set repair in concrete floors and pavements and is particularly useful where traffic must be kept flowing. The quick setting mortar will accept pedestrian and vehicular traffic in 2 hours. MonoBuild FPC mortar will be of particular interest to industrial maintenance engineers, transport managers, airport authorities or any place where that pot holes in concrete cause a hazard to pedestrian and wheeled traffic.
MonoBuild CLP is a cement based putty containing selected polymers to provide a smooth finished surface prior to application of decorative coatings. It is available in white and grey colours. to provide the water resistant, smooth finish levelling compounds for concrete masonry and bricks etc.
MonoBuild SP mortar is supplied as a ready to use dry powder requiring only the addition of water to produce a high strength mortar with non-shrink property along with controlled expansion characteristics. It is used for patching and replacement of worn out areas, filling of holes or depressions in concrete floor slabs in factories, godowns, commercial or domestic buildings .
MonoBuild EPC is a three part solvent-free combination of epoxy resin, modified amine hardeners filled with specially graded and selected high crushing strength, chemically inert aggregates Used for permanent repairs to concrete structure and cementitious substrates where strength, impermeability to water and resistance to aggressive chemicals is essential. Ideally suited for maintaining engineering, chemical handling and processing plants. It is applied by trowel as a durable chemical resistant repair mortar. The minimum thickness is 5mm. The maximum thickness is 50 mm.
MonoBuild Rapid is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a highly consistent, rapid setting mortar which is easy to apply in many difficult conditions. The material is based on a blend of cements, graded aggregates, special fillers and chemical additives which control the rate of set and minimise the risk of thermal cracking.
A two component paste, based on a bronze powder filled epoxy system. The non-rusting, nonmagnetic dependable inert putty extensively used for fairing, repair, filling or patching of bronze castings and equipment where bronze finish is desired and where brazing is undesirable or impossible.
MonoBuild FRC is a blend of dry powders and graded aggregates which requires only the site addition of clean water to produce a highly consistent, high strength, free flowing repair concrete which self-compacts, MonoBuild FRC exhibits excellent compatibility with concrete and good water repellent properties. For emergency reinstatement of damaged or deteriorated concrete. The material can be used internal or external surface.
MonoBuild HB is a Steel fibers blended , polymer modified repair mortar to provide high build properties as well as excellent resistance to chloride ions and the diffusion of acidic gases such as carbon dioxide. It contains special preblended cements, graded sands, Steel fibers and chemical additives which thermally combine to provide a product that has excellent compatibility with concrete as well as outstanding water repellent properties. MonoBuild HB can be applied in thicknesses from 10mm to 40mm in vertical and 25mm in overhead situations.
MonoBuild MC is The fluid micro‐concrete repair material shall be a single component, cement based, micro‐concrete to which only the site‐addition of clean water (and approved graded coarse aggregates where specified) shall be permitted. The micro concrete shall contain no metallic aggregates, or chloride sand shall be shrinkage compensated in the plastic state.
MonoBuild EM is a three‐component material supplied in pre‐weighed quantities ready for on‐site mixing and use. It is based on a high quality, solvent‐free, epoxy resin system; with special aggregates to provide high strength and excellent abrasion resistance
MonoBuild EC is a 2k polyurethane base elastomeric concrete. It consists of Specially Selected Aggregates it has consist of furnishing and installing suitable material to repair damaged concrete pavement. Spall repair shall consist of sawing concrete behind the spalled area, removing concrete pavement to expose sound pavement throughout the repair area, preparing and installing repair material and completion of the sawn joints etc.
MonoBuild DSP is a thixotropic, solvent free, two component compound based on water insensitive epoxy resins, inert fillers and thixotropic agents designed for applying in damp and submerged conditions. It is applied directly to concrete for filling cracks, blow holes etc., which cures to form a strong seal.
MonoBuild UMC is supplied as a ready to use dry powder requiring only the addition of water to produce a free flowing, non-shrink, repair material which exhibits exceptional resistance to 'washing out' of the cement phase when placed in stationary or moving water. The material is a mixture of specially processed cement, with carefully graded fine aggregate. Additives impart controlled expansion, water reduction and anti-washout characteristics. The aggregate grading is designed to aid uniform mixing, minimize segregation and bleeding whilst assisting the flow characteristics.
A two-pack zinc rich polyamide cured epoxy primer with metallic zinc powder. It provides a tough resistant coating with excellent mechanical and anti-corrosive properties. It provides cathodic protection on a local mechanical damage. It also has excellent adhesion on metal surfaces.
Monoguard SCG is a two-component, high solid phenolic Based coating. This coating provides excellent resistance to a wide range of chemicals and solvents and corrosion resistance, and is ideal for applications where abrasion resistance is needed. MonoGuard SCG was primary developed for barrier and protective coating related applications.
MonoGuard FP is a Epoxy Primer is fast setting, two‐component 100% solids, primer for the installation of Underlayments and Wear Toppings and can be used as a general primer. Epoxy Primer has been specifically formulated to accept a sand broadcast to work as a general purpose primer
Monobond AAC Primer is a single-component penetrating silane/ siloxane system which penetrates into porous substrates and then reacts to produce a bonded hydrophobic lining to the pores. It significantly reduces the absorption of water and water borne salts, whilst allowing the passage of water vapor gas out from the substrate. Monobond AAC Primer does not discolour the substrate and has excellent resistance to weathering