Building protects us from nature forces like rain, heat, cold, wind etc., The concrete structures on its own is porous and hence not watertight. The unprotected structures suffer from water induced damage including deterioration and corrosion caused by chlorination, oxidation and sulphation. They reduce alkalinity in concrete and turns acidic. The result, reinforcement bar catch rust and eventually expands, to drastically
hamper load bearing capacity of the building structures. The continuous presence of water leads to constant dampness & humidity and promotes the growth of molds and fungus on walls and insects presence leading to health problem like asthma, skin allergies, rashes etc., The consequent spalling of concrete plaster, flaking off expensive paint on interior/exterior ofwalls adversely impacts life and value of structure. If the buildings are notwaterproofed during constructions, itmay result in costlyandhassle pronerepairwork in future.
Monarch's technologically advancedMonoProof waterproofing systems cover every need of Building & Construction industry to protect from water ingress or loss of water through structures. The complete building structures frombasement to roof are protected from rising dampness, moisture, seepages and leakages from basement to roof. The technology ranges to acrylic SBR latex, crystalline, epoxy, water repellant polysiloxanes, polyurethane and bituminous based formulations. The coating fills and seals concrete pores, micro cracks and capillary tracts in joints,walls and floors through whichwater seep through and forms an integral waterproofing compound without breaking the existing brickbat cobaandconcrete screed.
MonoGuard ECG is a high build epoxy based surface protective coating specially formulated to provide a thixotropic surface lining material suitable for both vertical and horizontal surfaces. It cures to form a smooth hygienic film with good resistance to a wide range of mineral and organic acids, alkalis, fats and oils. The coating is hygienic and chemical resistant used for brick and concrete walls, concrete and metal tanks, sluices and ducts. The performance of the product is inversely proportionate to concentration of acids/alkalis and temperature.
MonoGuard FEC is 2 pack, solvent free epoxy material used for lining and Water proofing portal water retaining structures and surfaces subject to contact with food stuffs. The material cures to provide a smooth, hygienic and tough finish which is suitable for contact with potable water and foodstuffs. The cured film is resistant to corrosion, chemical attack and abrasion. The cured film is non-toxic and meets the requirements of IS: 9833 - 1981. The coating is designed to be applied in two coats to achieve a minimum total dry film thickness of 200 microns
MonoGuard MEC is a water dispersed epoxy coating designed for damp tolerant, anti-fungal and water vapor permeable coating. The product is odorless and can be applied onto cementitious and concrete surfaces providing dustproof coatings. The cured film is easily cleanable and resistant to penetration of oils and liquids. The product forms a waterproof barrier and is non-toxic. It is resistant to corrosion, chemicals and abrasion. It is additionally used as a thin coat application for the areas subject to light vehicle and pedestrian traffic. The product is ideal for contact with water intended for human consumption. The water permeability allows it to be applied on damp substrates and green concrete. However this should not be subjected to flowing / running water/over watered conditions.
Monoguard SCG is a two-component, high solid phenolic Based coating. This coating provides
excellent resistance to a wide range of chemicals and solvents and corrosion resistance, and is ideal for
applications where abrasion resistance is needed. MonoGuard SCG was primary developed for barrier and
protective coating related applications.
MonoGuard HBCT is a two‐component, polyamide cured, coal tar epoxy coating,
recommended for long‐term protection against corrosion under extreme conditions. provides
protection to concrete and metal structures against corrosion from aggressive environments. Suitable for
tanks above ground or in totally submerged conditions such as pipelinings. Particularly useful in sewage
works, effluent plants and dock and harbour installations.etc.
MonoGuard NE 120 is a two pack, high-build solvent free novolac epoxy coating designed for protecting new line pipes and pipeline protection. It is supplied in pre-measured quantities ready for site mixing and use. The material cures to provide a smooth, tough and resistant finish. Protective coating for concrete and steel used for high temperature service conditions up to 120°C. It is particularly useful to resist boiling water under continuous or partial service conditions etc.,
MonoGuard PS is a high build flexible epoxy polysulphide protective coating designed for
superior adhesion corrosion protection and high chemical resistance for concrete and steel structures.it has
excellent elastomeric coating with abrasion resistance. The inclusion of polysulfide polymers into the
backbone of the epoxy chain prevents the age hardening and rigidity of epoxy coatings.
A two component, heavy duty, abrasion resistant, glass flake reinforced vinyl ester coating and lining over steel and concrete for chemical, abrasion and temperature resistance is required. The coating is primary intended for the internal lining of chemical storage tanks and vessels where frequent contact with acidic/ aggressive chemicals or hot media are to be stored/immersed at temperatures up to 90°C (194°F) and for applications in areas where exposures to dry temperatures up to 160°C (320°F) are encountered